| SPECIFICATIONS
Telaire® 7001 |
| Method |
Dual Beam Absorption Infrared™ |
| Sample Method |
Diffusion or flow through (50-100 ml/min.) |
| Warranty |
18 months parts and labor |
| Performance |
| CO2, channel Measurment Range |
0-4,000 ppm voltage output/0-10,000 ppm display |
| Sensitivity |
± 1 ppm |
| Accuracy |
± 50 ppm or ± 5% of reading,
whichever is greater |
| Repeatability |
± 20 ppm |
| Temperature Dependence |
± 0.1% of reading per °C or ±
2 ppm per °C, whichever is greater, referenced to 25°C |
| Pressure Dependence |
0.13% of reading per mm Hg (corrected via user
input for elevation) |
| Annual Drift |
± 20 ppm typical |
| Response time |
<60 seconds for 90% of step change |
| Warm-up time |
<60 seconds at 22°C |
| Operating Conditions |
32-122 °F (0-50 °C)/0-95 RH, non-condensing |
| Storage Temperatures |
-40 to 140°F (-40 to 60 °C) |
| Calibration interval |
12 months offset adjustment using singles gas
at 0-1000 ppm CO2. Full factory calibration available |
| Temperature Channel |
| Temperature Range |
Voltage output: 32 to 104°F
(0 to 40°C) Display: 32 to 122°F (0 to 50 °C) |
| Display Resolution |
0.1 °F (0.1 °C) |
| Display Options |
°F, °C, or Off. Set with panel button. |
| Accuracy |
± 2 °F (± 1 °C) |
| Response Time |
20-30 minutes (case must equilibrate with environment) |
| Calibration Interval |
12 months, offset adjustment using temperature
standard at 50 to 86°F (10 to 30 °C). Full factory calibration available. |
| Output-Analog |
| CO2 |
0-4 VDC, 1mV/ppm (4,000 ppm max) |
| Temperature |
0-4 VDC, 1mV/ppm (0-40 °C) |
| Output Independance |
100 Ohms |
| Wiring connection |
Via Rj-45 to DB9 serial port cable (for use
with CO2View™ PC Graphing Software) |
| SPECIFICATIONS-DATALOGGING KIT |
| Temperature (internal sensor) |
| Range |
-4°F to + 158 °F Range for internal
sensor when used outside of case: -40 °F to + 158 ° (-40 °C to + 120 °C) |
| Accuracy |
± 1.27 º F (± 0.7 ±C)
at + 70 º F |
| Resolution |
0.7 º F (0.4 ºC) at 70 º F |
| Response time still in air |
15 min. typical with sensor inside case; i
min. typical with sensor outside case. |
| Relative Humidity (User-replaceable
RH sensor) |
| Range |
25% to 95% RH at +80ºF for intervals of ≥
10 seconds, non-condensing and non-fogging, see plot below |
| Accuracy |
± 5% |
| Response time |
10 min. typical in air |
| Sensor operating Environment |
+ 41°F to + 122°F non-condensing and
non-fogging |
| External Input |
Acceots the following sensors: Wide range of temp sensors (TMCx-Hx series). Split-core CTs for AC current (5 models). 4-20 mA input cable (CABLE-4-20 mA). 0-2.5 V DC input cable (Cable-2.5-Stereo) |
| External 2.5 Volt Input |
| 2.5 mm jack |
External input ground,
input, switched 2.5 V output; external input ground connection is not
the same as PC interface connection ground and should not be connected
to any external ground. |
| Input Range |
0 to + 2.5 Volts DC |
| Accuracy |
±10 mV ± 1% of reading |
| Resolution |
10 mV (8-bits) |
| Out Power |
+ 2.5 Volts DC at 2 mA, active only during
measurments |
| 7001 SPECIFICATIONS |
| Display |
LCD with independant CO2/Temperature
readings (panel buttons set elevation, °F/°C, calibration functions) |
| Power Supply |
| Battery Type |
Four AA batteries, not included |
| Battery Operation |
80 hours (alkaline) |
| External |
6 VDC from external AC/DC adapter, included |
| Power Requirements |
100 mA Peak, 20 mA average from 6V |
| Certification |
FCC Class 15 Part B |
| ACCESSORIES/ORDERING INFORMATION |
| 2075 Calibration Kit |
Come with regulator, tubing and gas. The kit
can perform up to 20 calibrations. |
| 2080 CO2 View™ |
Graphing Software for logging CO2 concentrations directly to a PC |
| APPLICATIONS |
• Identify Areas with low or substandard
ventilation
• Identify Hidden energy savings in over ventilated spaces
• Determine if ventilation is a factor in air quality complaints
• Locate the presence of combustion fumes from vehicles and appliances
• Use as a reference to calibrate wall mounted CO2 sensors |
About the CFM/Person Ventilation
Rate Measurment
The 7001 will calculate the outside air
ventilation rate to a space based on the inside/outside CO2 differential
readings. Outside readings can be established by measuring outside levels
and holding the "enter" button on the sensor for 5 seconds.
The outside reading can also be manually set using the - on-board keypad
and display (default 400 ppm).Accurate interpretation of the Ventilation
Rate Indicator requires a measuring 2 to 3 hours after occupancy has stabilized
in a space or at a peak in daily CO2 concentrations. In other conditions
the indicator may tend to over estimate ventilation rates. The ventilation
Rate display assumes a people activity level in the measured space similar
to an office type environment (1.2MET). If higher levels of activity are
present the indicator may tend to under estimate ventilation levels. |
e.jpg)