e.jpg)
| Springtest 1-2-3 Spring Testers |
|
|
| Basic tester (manual version) |
| A very simple, economical system for checking compression springs. The measurement head gives the force applied, the displacement sensor shows the flexion or height measured under load. The parallelism of the lower plate can be adjusted to ensure correct seating for the spring.  The pack includes: - BAT 750 R - CNR Easy force gauge (capacities of 10 N, 25 N, 50 N and 100 N available) - Mitutoyo ruler and fixtures - Compression plate diameter 50mm (AC PL50) - Self levelling compression plate (AC PAJ80) Technical characteristics of the CENTOR Easy force gauge: - Operates in tension and compression - Accuracy 0.1% FS - Resolution 1/10000 N - Peak function for tension and compression - Memory : 100 measures - Calculation of average and standard deviation - Simultaneous display of the peak and the current reading - Bar graph - 5 units available: N, kg, Lbs, g, Oz - Sampling rate 1 000 Hertz - Can be used with an external foot switch - Tare function - Auto-off adjustable from 5 to 15 min, can be deactivated - Programmable set point function - Two-way RS232 output: transmission of the current reading, minimum or maximum as desired - Digimatic output - 8 hours of operation without recharging - Fast charge - Reversible display - Backlit display - Sensor protected from overloads up to 200% of its capacity - Operates on rechargeable batteries - Low battery indicator - Memorizes its configuration - Metal casing with protective elastomer overmould - Threaded fixing holes on the back for use on test stand |
| Precision tester (manual version) |
A system specially designed for high precision measurements of compression. With its high reduction ratio, this manually operated test stand is well suited for the measurement of small springs with low force levels. The displacement sensor gives a measurement of the flexion or height measured under load with a resolution of 0.00002 in. The test stand is equipped with a set of adjustable limit stops. The measurement display shows the force and the displacement simultaneously and plots the graph curve for the spring. These data can be exported via the RS232 output of the display unit. The parallelism of the lower plate can be adjusted to ensure correct seating for the spring. An accessory kit can be used to make measurements on tension springs. The pack includes: - Special test stand - CNR DUAL T (in tabletop casing) (capacities of 10 N, 25 N and 50 N available) - incremental linear encoder linked to the CNR DUAL T with a SPIP connector - Compression plate diameter 100mm (AC PL100) - Self levelling compression plate (AC PAJ80) - Hook (CNR CRC) Technical characteristics of the CENTOR Dual force gauge: - Simultaneous readings on 2 channel - Operates in tension and compression - Accuracy 0.1% FS - Resolution 1/10000 N - Peak function for tension and compression - Simultaneous display of the peak and the current reading - Display of the Force/Displacement graph - Calculations of specific points in the graph for each channel: • Maxima • Force at time T • Break point • Derivative • First peak • Force on opening/closing of contact • Average force • Force for a given displacement - Memorization of the last graph curve measured - Bar graph - 5 units available: N, kg, Lbs, g, Oz - Sampling rate 1 000 Hertz - Can be used with a pedal - Tare function, separate on each channel - Automatic tare possible at the beginning of the graph curve - Auto-off adjustable from 5 to 15 min, can be deactivated - Programmable set point functions for each channel - Full two-way RS232 output - Running transmission of 25 value pairs per second - Possibility of transmitting the graph curve memorized - Digimatic output - Memorization of 2 configurations - Protection function (blocking) for the current configuration - Automatic recognition of additional force or torque sensors - Recognition of incremental displacement sensors (angular encoders or linear rulers) - Reversible display - Backlit display - Sensor protected from overloads up to 200% of its capacity - Operates on rechargeable batteries - 8 hours of operation without recharging - Fast charge - Low battery indicator - Metal casing with protective elastomer overmould - Threaded fixing holes on the back for use on test stand |
| Automatic tester (motorized version) |
With its CENTOR Dual force gauge; fixed plate and adjustable plate, this unit can be used to test high-capacity tension and compression springs. The command automatically determines the origin of the displacements and then stops the machine at a predetermined flexion value to measure the height under load. It is also possible to measure flexion, and cycles can be programmed. The instrument has an RS232 to store the results on a computer. Additional sensors are available to provide high levels of precision for springs with low force levels. The pack includes: - STENTOR - CNR DUAL T (in tabletop casing) (capacities of 250 N, 500 N, 1000 N available) or CNR DUAL R (with remote sensor) with adaptor for a capacity of 2500 N - Encoder for Drivepack and Centor linked to the CNR DUAL with a SPIP connector - Drivepack - Compression plate diameter 100mm (AC PL100) - Self levelling compression plate (AC PAJ80) Technical characteristics of the CENTOR Dual force gauge: - Simultaneous readings on 2 channels - Operates in tension and compression - Accuracy 0.1% FS - Resolution 1/10000 N - Peak function for tension and compression - Simultaneous display of the peak and the current reading - Display of the Force/Displacement graph - Calculations of specific points in the graph for each channel: • Maxima • Force at time T • Break point • Derivative • First peak • Force on opening/closing of contact • Average force • Force for a given displacement - Memorization of the last graph curve measured - Bar graph - 5 units available: N, kg, Lbs, g, Oz - Sampling rate 1 000 Hertz - Can be used with a pedal - Tare function, separate on each channel - Automatic tare possible at the beginning of the graph curve - Auto-off adjustable from 5 to 15 min, can be deactivated - Programmable set point functions for each channel - Full two-way RS232 output - Running transmission of 25 value pairs per second - Possibility of transmitting the graph curve memorized - Digimatic output - Memorization of 2 configurations - Protection function (blocking) for the current configuration - Automatic recognition of additional force or torque sensors - Recognition of incremental displacement sensors (angular encoders or linear rulers) - Reversible display - Backlit display - Sensor protected from overloads up to 200% of its capacity - Operates on rechargeable batteries - 8 hours of operation without recharging - Fast charge - Low battery indicator - Metal casing with protective elastomer overmould - Threaded fixing holes on the back for use on test stand |