Votre panier est vide !
 
Pour nous joindre
Contact
 
T: 514-354-2511
T: 1 800 463-4363
F: 514-354-6948
Tubulure pour échantillonnage de haute et basse densité Environnement

Tubulure pour échantillonnage de haute et basse densité

Fabricant :Waterra
Modèle :LDPE - HDPE


Besoin de plus d'informations? (514) 354-2511 - 1-800-463-4363

High Density Polyethylene (HDPE)

High Density Tubing provides the best performance in deeper monitoring wells because of it's rigidity. The stiffness of this material produces better flow rates and greater lifts. This tubing will also stretch much less than LDPE material in deeper monitoring wells, making it more efficient.

High Density Polyethylene also provides a stronger valve-tubing connection, especially with the male threaded valves, because it is stiffer and gives less when the valve is threaded into the tubing.

 

FEATURES

  • produced from virgin polyethylene resins
  • Waterra does not use any regrind product in any of our tubing
  • does not contain any UV stabilizers*
  • coils of tubing are individually poly bagged and are stored in sealed boxes, protected from UV light sources
  • Waterra Foot Valves are guaranteed to properly fit onto and into Waterra tubing.

*Leaving non UV protected polyethylene tubing exposed to sunlight or a UV light source will result in the material becoming brittle. The material will then fracture very easily. Keep the tubing protected from these light sources until you're ready to install it in your well and it will last for may years.

 

Low Density Polyethylene (LDPE)

Low Density Tubing is the most popular tubing choice for use in shallow monitoring wells. LDPE tubing is more flexible than HDPE and is less likely to develop a kink. The difference in rigidity between LDPE and HDPE does not have a significant impact on the performance of the inertial pump in shallow wells. LDPE tubing is also recommended for use with the Proactive line of 12 volt submersible pumps.

FEATURES

  • produced from virgin polyethylene resins
  • Waterra does not use any regrind product in any of our tubing
  • does not contain any UV stabilizers*
  • coils of tubing are individually poly bagged and are stored in sealed boxes, protected from UV light sources
  • Waterra Foot Valves are guaranteed to properly fit onto and into Waterra tubing.

*Leaving non UV protected polyethylene tubing exposed to sunlight or a UV light source will result in the material becoming brittle. The material will then fracture very easily. Keep you tubing protected from these light sources until your ready to install it in your well and it will last for may years.

 

STANDARD FLOW TUBING SPECIFICATIONS
Dimensions 5/8" OD X 1/2" ID
Coil lengths 100', 200', 500'
For use with D-25, D-16, SS-19, SS-16

 

HIGH FLOW TUBING SPECIFICATIONS
Dimensions 1" OD X 0.814" ID
Coil lengths 100', 200'
Dimensions 1" OD x 0.75" ID
Coil lengths 300'
For use with D-32, SS-32

 

LOW FLOW TUBING SPECIFICATIONS
Dimensions 0.5" OD X 0.375" ID
Coil lengths 100', 500'
For use with D-13, SS-13

 

MICRO FLOW TUBING SPECIFICATIONS
Dimensions 0.375" OD X 0.25" ID
Coil lengths 100'
For use with SS-10

 

VOC TUBING SPECIFICATIONS
Dimensions 0.25" OD X 0.170" ID
Coil lengths -100', 500'
For use with -VOC Sampling
-Filtering bailer samples
Etiquettes : Tubage, 5/8’’, ½’’, 3/8"

Convertisseur d'unités